21 Ruru St, Eden Tce. Ph: +64 9 379 5150 Fax: +64 9 379 3303 Email Icon

10kg/2L

CODE: VEPRIMERSF!

Primer SF

Single component polyurethane solvent-free primer

Single component polyurethane moisture-cure primer that is water and solvent-free for treating subfloors before laying wood floors. The low level viscosity and the excellent penetration make it ideal for strengthening and waterproofing concrete and anhydrite screeds with a high level of moisture up to a maximum of 5% M.C. (up to 2.8% M.C. with just one coat). It is recommended especially for screeds with built-in heating. Moreover, the absence of solvents makes it safe for transportation and storage (non- flammable product) and when applied (odourless, it can also be used in the vicinity of rooms that are in use). Compared with products containing water, PRIMER SF offers a much higher coverage and does not increase the humidity of the screed.

60 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1
  • Solvent-free
  • Very high resistance to humidity (≤ 5% M.C.)
  • Performance certified by an external independent authority
  • Low level viscosity for deeper penetration
  • Absence of oiliness on the surface for a perfect adhesion of the adhesive
Technical Notes
Completely dry (hours)24
Average coverage per coat (g/m2)150/250
Calculated VOC (g/lt)0

5+2.5 Lt

CODE: VEEPO2

Primer EPO 2

Two component epoxy primer

Two component water and solvent-free epoxy primer for treating subfloors. It can be used to treat crumbly screeds or screeds with a high level of residual humidity up to a maximum of 5% M.C., as well as being suitable as a binder for the preparation of synthetic mortar for quick repairs.

37.5 sqm cover

  • Quick Facts
  • Very high resistance to humidity (≤ 5% M.C.)
  • Solvent-free
  • Ideal for rooms with little ventilation and/or those in use
Technical Notes
Catalysis ratio (Vol/Vol)2:1
Pot Life at a room temperature of 10°C (min.)35
Pot Life at a room temperature of 20°C (min.)28
Pot Life at a room temperature of 30°C (min.)15
Overcoating (hours)5-16
Completely dry (hours)24/48
Average coverage per coat (g/m2)150/250

9 + 1 kg

CODE: VEZERO%

Zero%

Two component epoxy polyurethane solvent-free adhesive

A new generation two component epoxy polyurethane solvent and water free adhesive for gluing wood flooring of any size on concrete screeds, including heated ones and on non-absorbing surfaces (ceramic tiles, stoneware, marble, etc.). It is also ideal for laying planks and engineered wood floors. A real evolution: ZERO % asserts itself in a new version with an improved rheology making it easier to spread and leading to a perfect ridge height. ZERO % is outstanding for the fact that it is almost insensitive to changes in the temperature (seasonality), completely odour-free both before and after mixing, and offers excellent hold and wettability under any environmental condition. The coverage has also been considerably improved. The high coefficient of elasticity after hardening completes the features of the ZERO % revolutionary adhesive together with its unbeatable characteristics of adhesion and toughness.

10 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1
  • Solvent-free
  • Very good reactivity even at low temperatures
  • Sensitivity to temperature changes (seasonality) has been eliminated - consistent viscosity
  • Considerably reduced odour of component B
  • Excellent coverage
  • Excellent spreadability
  • Perfect ridge height
Technical Notes
Pot-life (hours)2
Open time (min.)60
Ready for traffic (hours)24/48
Interval before sanding (days)3
Average coverage (g/m2)900/1400

12 kg

CODE: VEZEROMONO

Zeromono

Single component high performance adhesive with silanic termination

Single component moisture-cure silane-terminated adhesive that does not contain water, solvents, isocy- anates, epoxy or amino compounds and for this reason does not bear any health or risk warnings or sym- bols. The EC1 PLUS classification certifies the very low emission of volatile organic compounds both when being applied and once the floor is in use.

17 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1 PLUS
  • Certified soundproofing qualities (insulation from footsteps)
  • Certified Heat Resistance
  • No hazard labels
  • Exceptional adhesion
  • Permanent elasticity
  • Does not stain pre-finished floors, no marks
  • High level coverage
  • Perfect ridge height
Technical Notes
Open time (max. registration time) (min.)45/60
Open time (surface skin formation time) (min.)100/120
Ready for traffic (hours)24
Interval before sanding (days)4
Average coverage (g/m2)800/1000

12 kg

Monosil 600 – 600 ml

CODE: VEZEROMONO

Monosil

Single component silane-terminated adhesive

Single component silane-terminated moisture-cure adhesive. MONOSIL does not contain water, solvents, isocyanates, epoxy or amino compounds or heavy metals (tin) and consequently does not bear any health or risk warnings or symbols. MONOSIL has excellent adhesion characteristics on all subfloors as well as permanent elasticity. These characteristics make it the ideal adhesive for laying engineered and traditional solid wood floors of average size on all subfloors, with or without underfloor heating. MONOSIL does not harm the coating of pre-finished wood floors and for this reason does not leave any marks; other features of this adhesive are the ease with which it can be worked, the high level coverage, resistance to water and the capacity to absorb sound leading to a considerable improvement in the comfort of the environment with regard to noise levels.

15 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1 PLUS No hazard label
  • Excellent coverage
  • Excellent spreadability
  • Perfect ridge height
  • High sound absorbing capacity
  • Available in a sausage pack version - Monosil 600
Technical Notes
Open time (max. registration time) (min.)45/60
Open time (surface skin formation time) (min.)120/150
Ready for traffic (hours)24
Interval before sanding (days)5
Average coverage (g/m2)800/1000

310 ml

Gap Filler

Coloured acrylic sealer

GAP FILLER is an acrylic sealant in a solvent-free watery dispersion for wood and laminate floors. Available in the colours WHITE, MAPLE, OAK, DOUSSIÉ, MEDIUM WALNUT, DARK WALNUT and WENGÉ.

  • Quick Facts
  • Very elastic
  • Suitable for filling expansion joints
  • Suitable for gluing skirting boards
  • Can be sanded and overcoated
  • Removable with water when still wet
Technical Notes
Open time (min.)10 20
Flexibility7 %
Overcoating (hours)4 - 6

10 Lt

CODE: VELEGASTUCOPLUS

Lega Stucco Plus

Low odour binder for fillers

Single component solvent based binder for preparing fillers for sealing wood floors.

100 sqm cover

  • Quick Facts
  • Low odour
  • Long workability
  • Excellent coverage
  • Suitable for smoothing and sealing large cracks and/or knots
Technical Notes
Completely dry (min.)35
Overcoating (min.)35

10 L

CODE: VEFLASH

Flash

Very fast drying single component sealer

Very fast drying single component sealer with a nitrocellulose base for wood floors. The rapid drying time makes the product particularly suitable for fast finishing cycles. It can be overcoated without sanding even using single component waterborne finishes.

100 sqm cover

  • Quick Facts
  • Very fast drying
  • Effective pore closure
  • Makes subsequent coats of paint uniform and limits their absorption
  • Can be overcoated without sanding
  • Considerable water repellent action
Technical Notes
Completely dry (min.)30
Overcoating (min.)30

10 + 10 lt

CODE: VEPRIMERS

Ultra Tenax

Two component polyurethane sealer

Two component polyurethane sealer with a very high solid content. Formulated specifically for minimizing the risk of “stripping” with the consequent appearance of light patches when used together with two component waterborne finishes.

180 sqm cover

  • Quick Facts
  • High build level
  • Suitable for mixed cycles with two component waterborne finishes
  • Very high resistance to abrasion
  • Easy to sand
Technical Notes
Catalysis ratio (vol/vol)1:1
Dry for sanding (hours)6 (Recommended 16)
Pot-life (hours)3
Overcoating (hours)6
Overcoating for maximum performance (hours)16

5 Lt

CODE: VEZEROFILLER

Zero Filler

Waterborne binder for fillers

Solvent-free waterborne binder for preparing fillers to seal wood floors. It is blended with wood flour obtained by sanding with a fine grit sandpaper to create a filler of the same colour as the floor. Ideal for waterborne coating cycles. Zero emissions. Not suitable for Merbau.

50 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1 PLUS
  • Solvent-free
  • Fast drying
  • Ready for sanding after 1 hour
  • Completely odourless
  • Long workability
  • High solid content
  • Greater elasticity
  • Can already be sanded in the intermediate phase with a 60/80 grit sandpaper
Technical Notes
Completely dry (min.)60
Ready for sanding (min.)60
Ready for coating (min.)60
Average coverage (g/m2)100/120
Application methodStainless steel/plastic trowel

12 kg

CODE: VEFILLER

Filler

Water based ready to use filler

Water based ready to use filler for sealing wood floors, fast drying and easy to sand. Ideal for waterborne and solvent based finishing cycles. Available in the shades: OAK, WALNUT and DOUSSIÉ.

  • Quick Facts
  • Ready to use
  • Easy to sand
Technical Notes
Application methodStainless steel or plastic American trowel
Dry for sanding (min.)30

5 Lt

CODE: VEAQUAFIRST

Aqua First

Single component waterborne sealer

Single component waterborne sealer featuring an excellent filling capacity, fast drying time and good shading of the wood.

50 sqm cover

  • Quick Facts
  • Ease of sanding
  • Fast
  • Good toning effect
Technical Notes
Dry for sanding (hours)2
Overcoating without sanding (hours)within 2 (when completely dry)

5 + 1 Lt

CODE: VEAQUATENAX!

Aqua Tenax

Two component waterborne sealer

Two component waterborne sealer featuring a high level insulating capacity, excellent coverage, good sandability and ease of application. The most important feature of this sealer is that it minimizes problems of overlapping. AQUA TENAX has been formulated to give a pleasant shade to the wood without causing unwanted changes to the colour of those woods rich in tannin and other water soluble staining substances (oak, teak…). For this reason, it is recommended especially for difficult woods such as IPE LAPACHO when browning or reddening would be undesirable. Thanks to its high level of solid content, AQUA TENAX can be used in combination with the two component finishes in the INNOVATION range, to carry out two coat finishing cycles.

60 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1
  • High build property
  • Good sandability
  • Low emission
  • Minimizes overlapping
  • Ideal for 2 coat cycles
Technical Notes
Catalysis ratio (vol/vol)5:1
Dry for sanding (hours)12
Overcoating without sanding (hours)After 3, within 6

5 + 1 Lt

CODE: VEFLAME!

Flame

Two component waterborne sealer with toning effect

Two component waterborne sealer with a very low content of volatile organic compounds (VOC). The composition of the product based on the latest generation of resins allows the wood to appear in almost the same way as traditional solvent based sealers. Unlike the latter, this product does not cause yellowing over time, preventing excessively dark or unnatural changes in the colour of the wood. This distinctive characteristic of FLAME has been achieved without penalizing other very important qualities such as resistance to the formation of overlapping, considerable coverage, ease of application and sanding. Thanks to its high level of solid content, FLAME in combination with the two component finishes in the INNOVATION range, allows a two coat cycle to be carried out.

60 sqm cover

  • Quick Facts
  • High toning power
  • High build property
  • Good sanding qualities
  • Low emission
  • Minimum overlapping
  • Ideal for 2 coat cycles
Technical Notes
Catalysis ratio (vol/vol)5:1
Dry for sanding (hours)16
Overcoating without sanding (hours)After 3, within 8

5 Lt

CODE: VESOLUZIONE

Soluzione

Blend of low volatile solvents for diluting waterborne systems

Blend of coalescences with graduated evaporation to be added to waterborne products to increase the open time and improve the workability. Recommended particularly for hotter periods of the year and for carrying out more demanding jobs.

  • Quick Facts
  • The addition of this product to coatings complying with
  • EC DIR. 2004/42 could raise the VOC value above the permitted limits.
Technical Notes
AppearanceTransparent liquid
Max. permitted dilution10%

5 + 0.5 Lt

1 + 0.1 Lt

CODE: VEARTWORK

Artwork

Two component waterborne pigmented treatment

Two component waterborne pigmented treatment featuring top rate coverage, ease of application and excellent levelling. ARTWORK offers a considerable insulating capacity of the tannins and other wood extracts and for this reason, it enables lighter shades to be achieved even on critical woods such as chestnut and oak. With ARTWORK wood floors and wood surfaces can be given any colour: in fact ARTWORK is available, on request, in all RAL shades.

61 sqm cover

  • Quick Facts
  • Excellent coverage
  • Easy to use
  • Great tannin insulating capacity
  • Available on request in all RAL shades
Technical Notes
Catalisys ratio (vol/vol)10:1
Dust dry (min.)25
Impression dry (min.)40
Completely dry (hours)12
Dry for sanding (hours)12
Overcoating (hours)after 3, within 5
Application methodRoller, brush

5 Lt

CODE: VESILK

Silk

Single component waterborne finish

Single component polyurethane waterborne finish featuring exceptional resistance to abrasion and to scuff marks which makes it ideal for use in every situation. From the point of view of appearance, it differs from traditional waterborne products due to its considerable transparency, for the cleanliness of the film and above all for the warm tone that it confers on the wood, avoiding the “whitening” typical of other waterborne finishes.

62 sqm cover

  • Quick Facts
  • Exceptional resistance to abrasion and to scuff marks
  • Great transparency
  • Good toning effect
Technical Notes
Completely dry (hours)8
Dry for sanding (hours)8
Overcoating without sanding (hours)After 3, within 5
Degree of gloss SILK 30 (gloss)30
Degree of gloss SILK 60 (gloss)60
Degree of gloss SILK 90 (gloss)90

5 Lt - 0,35 Lt BOOST

CODE: VEZEROVOC

Zero VOC

Single/two component waterborne finishing treatment

Protective waterborne finish that is completely solvent-free. ZERO VOC can be used both as a single component or as a two component finish after adding ZERO VOC BOOST. Produced with renewable raw materials, ZERO VOC is ideal for green building and when applied directly on the wood it leaves the shade unaltered and provides a very natural effect. ZERO VOC is the first specific product for wood flooring to join the SUPER COMPLIANT ARCHITECTURAL COATINGS MANUFACTURERS LIST.

50 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1 PLUS
  • Zero Voc
  • Highly ecological – re-use of leftover product - no wastage
  • Hardener has no hazard label
  • Solvent-free
  • Formulated with renewable raw materials
Technical Notes
Completely dry (min.)6
Dry for sanding (hours)3
Degree of gloss - Zero VOC X-MATT 15 (gloss)15
Degree of gloss - Zero VOC 30 30 (gloss)30
Degree of gloss - Zero VOC 60 60 (gloss)60

5 + 0.5 Lt

CODE: VEIDRO2K

Idro 2K

Two component waterborne finish

Two component polyurethane waterborne finish. In the “natural wood effect” version, IDRO 2K confers a natural appearance to floors together with a uniformity and cleanliness that can only be compared to the results achieved with impregnation cycles with oil and/or wax. Apart from these features regarding appearance, IDRO 2K combines qualities of resistance to abrasion and to rubber marks never before achieved by waterborne products so it is even recommended for use on heavy duty flooring (in salons, shops, etc.). If it is applied directly without a sealer, it brightens up the colour of the wood quite considerably, without leading to yellowing over time.

61 sqm cover

  • Quick Facts
  • Low environmental impact certified EC1
  • Extraordinary chemical and mechanical resistance
Technical Notes
Catalysis ratio (vol/vol)10:1
Completely dry (hours)12
Dry for sanding (hours)12
Overcoating without sanding (hours)After 3, within 5
Degree of gloss 2K (gloss)10
Degree of gloss 2K EXPORT (gloss)30
Degree of gloss 2K SAT (gloss)50

1 Lt

CODE: VEC.OIL

Color.Oil

Oil wood stain

Stain based on modified vegetable oils designed to colour and impregnate indoor wood floors in just one operation. Easy to use, it stains wood floors evenly, penetrating deep down and protecting the wood against mildew and dry rot. Suitable for all types of wood, although it produces the best results and is recommended for use on large grain woods such as oak, larch, chestnut, etc. Color.Oil can be overcoated with Fix.Oil, waterborne finishes or oleo-urethane finishes. Available in various shades that can be blended together in any proportion, making the range of colours practically limitless. For use of Color.Oil white and grey, consult the relevant technical data sheet.

25 sqm cover

  • Quick Facts
  • Easy to use
  • Protects the wood against mildew and dry rot
  • Available in various shades that can be blended together
Technical Notes
Application methodRoller, brush, pad
Average coverage per coat (g/m2)30/50
Interval before polishing (min.)5/10
Interval before coating with fixative without sanding (hours)Minimum 16

10 Lt

CODE: VEV15SEALER!

V 15

Single component sealer

Single component non-yellowing vinyl resin based sealer. Formulated specifically so that it can also be overcoated with single component solvent based polyurethane finishes, it is recommended particularly for all those cycles in which the colour change of the floor has to be limited.

100 sqm cover

  • Quick Facts
  • Fast drying
  • Effective pore closure
  • Makes subsequent coats of paint uniform and limits their absorption
  • Considerable water repellent action
Technical Notes
Completely dry (min.)30
Overcoating (min.)30

3Lt

CODE: VEFIXOIL!

Fix.Oil

Highly resistant oil

A fixative based on natural oils and waxes to be applied after impregnating with Pro.Oil or Color.Oil. It protects the wood against water and other substances in daily use (coffee, alcohol, etc.) preventing permanent staining. It increases the resistance to abrasion of oiled floors. For use on Color.Oil white and grey, use only FIX.OIL “LIGHT”.

75 sqm cover

Technical Notes
Application methodRoller, Brush, Pad
Average coverage per coat (g/m2)30/50
Max. interval before polishing (min.)5/10

5Lt

CODE: VEZERODECK

Zero Deck

High performance eco-friendly water-oil for outdoor use

High performance impregnating water-oil formulated specifically for outdoor use. ZERO DECK not only brings out the smoothness but also brightens the tone of the wood. Free of heavy metal hardeners, it does not give rise to phenomena of self-combustion like traditional oils. Although its VOC values are insignificant, ZERO DECK is a product for outdoor use and, therefore, EC1 classification is not provided for.

66 sqm cover

  • Quick Facts
  • Greater coverage compared with traditional products
  • Excellent shading property
  • Greater penetration in the wood compared with a solvent based product
  • Easy to restore: it does not require sanding
  • Protection against dry rot
  • Protection against UV rays
  • Prevents greying maintaining the natural colour of the wood
  • Excellent water repellence
Technical Notes
Application methodRoller, Brush or Pad
Average coverage per coat (g/m2)50/100
Interval before the second coat (hours)After 6, within 24

3Lt

CODE: VEDECKOIL!

Deck.Oil

Impregnating oil for outdoor use

A vegetable based impregnating oil consisting of a balanced blend of various oils (linen, wood, etc.) formulated specifically for outdoor use. DECK.OIL brings out the features of softness and warmth while enhancing the grain of the wood.

60 sqm cover

Technical Notes
Application methodRoller, Brush, Pad
Average coverage per coat (g/m2)50/80
Interval before polishing (min.)5/10

3Lt

CODE: VEPRIMERSF

Deck.Oil Strong

High performance impregnating oil for outdoor use

A vegetable based impregnating oil consisting of a balanced blend of various oils (linen, wood, etc.) formulated specifically for outdoor use. DECK.OIL Strong brings out the features of softness and warmth while enhancing the grain of the wood.

75 sqm cover

Technical Notes
Application methodRoller, Brush, Pad
Average coverage per coat (g/m2)40/100
Interval before polishing (min.)5/10

1 Lt

CODE: VEDECKCARE

Deck.Care

Maintenance product for oil treated indoor and outdoor floors (routine maintenance)

DECK.CARE is an emulsion of waxes, natural oils, modified oils and special anti UV additives for the maintenance of outdoor floors treated with DECK.OIL, DECK.OIL STRONG, ZERO.DECK or indoor floors treated with the W.OIL range (PRO.OIL, FIX.OIL). Cobalt and Methyl Ethyl Ketoxime-free. The oil component of DECK.CARE restores the treatment oil that has deteriorated due to exposure to atmospheric agents and it penetrates into the wood providing in-depth protection, the water repellent wax prevents water from entering the pores in the wood, while the anti-UV additives delay the deterioration of the lignin. DECK.CARE is also suitable for protecting indoor oil treated wood floors and all wood products treated with impregnation products, both indoors and out (garden furniture, wooden partitions, beams, fences…). Recommended particularly as a protective treatment for WPC.

Technical Notes
Application methodRoller, Brush, Pad, Beige Pad
Dilution in water20/25%
Recommended frequency of useonce every 1-2 months
Ready for traffic (min.)30
Ready for traffic and for max. performance (hours)12

5 Lt

1 Lt

Deck.Reset

Pre-treatment for outdoor wood floors and manufactured products

A highly effective watery solution for removing the grey patina on outdoor decking and wood products caused by the deterioration and washing away of the lignin. Use of DECK.RESET restores the original colour of the wood that is then protected with DECK.OIL, DECK.OIL STRONG and ZERO.DECK. DECK.RESET can be used on flooring, garden furniture, wooden gazebos and on all wood items located outdoors. It is recommended especially as a strong detergent for WPC.

Technical Notes
Application methodSpray, Roller, Brush, Pad
Average coverage per coat (g/m2)50 with spray or pad, 80 with roller or brush
Operating time for using trowels, brushes, pads (min.)10
Operating time for using a pressure washer (min.)From 10 to 20